IR15-21C-L10资料

Technical Data Sheet

1206 Package Chip Infrared LED

IR15-21C/L10 Features

․Small double-end package ․High reliability

․Low forward voltage ․Good spectral matching to Si photodetector ․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

IR15-21C/L10 is an infrared emitting diode in miniature top view flat SMD package and it is molded in a water

clear plastic. The device is spectrally matched with silicon photodiode and phototransistor.

Applications

․PCB mounted infrared sensor

․Infrared emitting for miniature light barrier ․Floppy disk drive ․Optoelectronic switch ․Smoke detector

Device Selection Guide LED Part No.

Chip Material

Lens Color

IR GaAlAs Water Clear

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 1 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10

Package Dimensions

Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm

Parameter SymbolContinuous Forward Current Peak Forward Current*1 Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature*2 Power Dissipation at(or below) 25℃Free Air Temperature

Absolute Maximum Ratings (Ta=25℃)

Rating Units IF 65 mA

IFP 1.0 A VR 5 V Topr Tstg

-25 ~ +85 -40 ~ +100

℃ ℃

Tsol 260 ℃ Pd 130 mW

Notes: *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%. *2:Soldering time≦5 seconds.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 2 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Condition Min. Typ. Max. Units IF=20mA mW/sr Ee Radiant Intensity 0.2 0.8 -- IF=20mA λp Peak Wavelength -- 940 -- nm Spectral Bandwidth Forward Voltage Reverse Current View Angle

Δλ VF IR 2θ1/2

IF=20mA IF=20mA

--

45

--

nm

-- 1.2 1.5 V

VR=5V -- -- 10 μA

IF=20mA -- 160 -- deg Intensity Specifications for Bin Grading

Rank Test Condition E F G H

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 3 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

Min

Max

Unit

0.2 1.0 IF=20mA

0.5 1.5 mW/sr

1.0 2.5 2.0 3.5 元器件交易网www.cecb2b.com

IR15-21C/L10 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Fig.2 Spectral Distribution Ambient Temperature 140120100806040200 10080604020020406080100IF=20mATa=25°C-250Fig.3 Peak Emission Wavelength Fig.4 Forward Current Ambient Temperature vs. Forward Voltage 980960 410310940920900-25210025507510011001234 Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 4 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai 元器件交易网www.cecb2b.com

IR15-21C/L10

Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Forward Current Angular Displacement -20-100101002030Ie-Radiant Intensity(mW/sr)101.00.940506070800.60.40.200.20.40.610.80.701230.110101010104IF-Forward Current (mA)Fig.7 Relative Intensity vs. Fig.8 Forward Voltage vs. Ambient Temperature(°C) Ambient Temperature(°C) 1.0 1.30.8IF=20mA1.2IF=20mA0.61.10.42550751001201255075100120 Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 5 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10 Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 6 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10 4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 7 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10

Reliability Test Item And Condition

The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10%

NO. Item Test Conditions

Test Hours/Sample Failure Cycles Sizes Judgement

Criteria

Ac/Re

1 REFLOW SolderingTEMP.：260℃±5℃ 6Mins 22pcs

IR≧U×2 5secs

2 Temperature Cycle H : +100℃ 15mins50Cycles 22pcs Ee≦L×0.8

VF≧U×1.2 5mins

L : -40℃ 15mins

3 Thermal Shock

H :+100℃ 5mins50Cycles 22pcs U：Upper

Specification Limit L：Lower 1000hrs 22pcs Specification Limit 1000hrs 22pcs

0/1 0/1

0/1

10secsL :-10℃ 5mins

4 High Temperature TEMP.：+100℃ Storage 5 Low Temperature TEMP.：-40℃ Storage

0/1 0/1 0/1 0/1

6 DC Operating Life IF=20mA 1000hrs 22pcs 1000hrs 22pcs 7 High Temperature/ 85℃ / 85% R.H High Humidity

Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 8 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai

元器件交易网www.cecb2b.com

IR15-21C/L10

Packing Quantity Specification 1.1000PCS/1Bag，20Bags/1Box 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHSIR15-21C/L10 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-61, 2267-6306 Taipei 236, Taiwan, R.O.C http:\\\\www.everlight.com Tucheng, EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936 Everlight Electronics Co., Ltd. http:\\\\www.everlight.com Rev 3 Page: 9 of 9 Device No：DIR-152-124 Prepared date：07-20-2005 Prepared by：Jaine Tsai